How to Fix Electrolux Washer Error CL
Control Lock (Child Lock) is activated.
515 repair guides
Choose the appliance, then find the exact code. Every guide leads with what the code means, what to try first, and whether a part or replacement is worth considering.
Electrolux
Control Lock (Child Lock) is activated.
Electrolux washer code LOC indicates control lock activated. Audited diagnosis findings: the control lock (child lock) feature has been activated.
Water Leakage / Suds / Blocked Filter - General error for water leakage, excessive suds, or a blocked filter.
Electrolux washer code EF4 indicates no flowmeter signal. Audited diagnosis findings: water supply faucet is turned off; kinked or blocked…
Incongruence between the programme selector version and the configuration data stored on the main control board.
Water level sensor detects overfill.
Door lock triac fault.
Drawer reed switch not closed.
Drying heater error.
The door is not closed.
Door switch error or excessive suds detected.
Problems with too low voltage of the power supply.
Zero Watt relay alarm; low power supply voltage.
Safety relay problem on the electronic board.
A data communication error has occurred between the WD board and the main PCB.
Indicates a fault with the drying heating element relay 1.
Signals a fault with the drying heating element relay 2.
A general fault indicating faulty wiring, a defective WD board, or a faulty main PCB.
There is no communication between the main PCB and the display board.
Appears in demo mode.
The wash cycle has finished.
Reversed hot and cold water hoses.
Reversed hot and cold water hoses.
Reversed hot and cold water hoses.
Reversed hot and cold water hoses.
Control board error.
No spray arm detection; the spray arm cannot rotate properly or there is a faulty sensor.
Low water pressure.
Electrolux Washer Error PO — Power failure.
The machine is in a reset state.
Thermistor error.
Unbalanced load detected.
Touch sensor on the user interface is not responding.
Frequency of power out of limits.
Supply voltage too high.
Electrolux washer code B3 indicates supply voltage too low. Audited diagnosis findings: excessively high voltage from the power outlet; visible…
Indicates an imbalance between the pressure switches.
The machine is not taking in water.
Electrolux washer code C2 indicates the machine is not draining. Audited diagnosis findings: kinked or clogged drain hose; clogged drain…
Electrolux washer code C3 indicates water leak detected. Audited diagnosis findings: water leak from hoses or tub; clogged or disconnected…
Problem with the draining pump.
Excessive heating in the motor (thermal fuse).
Electrolux washer code C6 indicates pressure switch fault. Audited diagnosis findings: blocked or kinked pressure switch hose; loose wiring connection…
Electrolux washer code C7 indicates heating element fault. Audited diagnosis findings: no hot water supply to the washer; visible damage…
Temperature sensor problem.
Indicates an imbalance during a spin cycle or a motor fault.
Motor triac short circuit.
Motor tacho signal missing.
Water inlet valve triac fault.
Electrolux washer code CF indicates eEPROM error. Audited diagnosis findings: communication error between the main control board and the user…
The washing machine is in demonstration mode and will not operate a wash cycle.
Electrolux washer code DN indicates demo mode is activated. Audited diagnosis findings: the washer is in demonstration or store mode.
This code is not consistently defined across sources, but generally points to an issue with a pressure switch or water…
Insufficient water supply.
Electrolux washer code E02 indicates door is open. Audited diagnosis findings: door is not firmly closed; clothing or other object…
Electrolux washer code E03 indicates door is unlocked. Audited diagnosis findings: door lock mechanism is obstructed; the control board is…
Electrolux washer code E04 indicates low water temperature. Audited diagnosis findings: open circuit in the temperature sensor; loose or damaged…
Electrolux washer code E05 indicates high water temperature. Audited diagnosis findings: short circuit in the temperature sensor; loose or damaged…
Water level is too high at the end of a program.
Electrolux washer code E07 indicates water overfill. Audited diagnosis findings: water overfill condition; water inlet valve is stuck open and…
Heating error or defective heater.
Water inlet fault; the machine is not taking in water or the water pressure is too low.
The appliance is not filling with water during the washing phase of the cycle.
The washer is not filling with water during the rinse phase.
A water leak has been detected.
Failure in the ignition control to detect a flame (for washer-dryer models with gas heating).
Draining problem; the machine is not draining water.
Draining fault, specifically that water has not been removed from the tank within a set time.
The washing machine is not draining after the rinse cycle.
Fault with the drain pump triac, which controls the drain pump.
Fault in the sensing circuit of the drain pump triac.
An incorrect input signal is being sent to the microprocessor.
Signals a problem with the door lock mechanism.
Water pressure sensor problem.
Electrolux washer code E31 indicates faulty pressure switch. Audited diagnosis findings: faulty pressure switch; blocked or kinked pressure switch hose.
Calibration problem with the pressure switch.
Inconsistent operation of water level sensors.
Incongruency between the electronic pressure switch and the anti-boiling pressure switch level for over 60 seconds.
The water level is too high.
Breakdown of the sensor that prevents the heating element from turning on without the required water level.
Malfunction of the first water level sensor (I).
Blocked pressure chamber or pressure-sensing hydraulic circuit.
Malfunction of the water overflow level sensor.
Heating element relay sensing faulty; input signal to microprocessor is consistently 0V or 5V, indicating a faulty circuit board.
Water level in the drum is too high.
Door Lock Error (Variant) - Similar to E30, often related to the door switch or latch.
The door is not closed tightly.
Malfunction of the door lock.
Malfunction of the lock triac.
Breakdown of the door closing sensor.
Malfunction in the door lock control circuit on the electronic controller.
Door is detected as open while the control board is trying to lock it.
Problem with the temperature sensor (NTC).
Motor / Inverter Error - Issue with the drive motor or its control system.
Short circuit in the drive motor's control element (triac).
No signal from the tachometer generator to the electronic controller.
Malfunction of the drive motor control circuit.
Failure of one of the two contact groups of the drive motor reversing relay.
Electrolux washer code E55 indicates motor overheating. Audited diagnosis findings: motor circuit malfunction; faulty speed control board; jammed motor or…
Electrolux washer code E56 indicates high motor current. Audited diagnosis findings: high current to the motor; motor overheating; faulty motor…
High current on inverter.
High current on motor phase.
No tachometer signal for 3 seconds after the motor has started.
High temperature on the heat sink of the electronic control board.
Motor control under voltage.
Input voltage is too high (over 430V).
Communication problem between the main control board and the motor control board.
Motor control is continuously resetting.
Problem with the heating element.
Heating Error - Washer not heating water or taking too long to heat.
Insufficient heating; the water does not reach the programmed temperature.
Overheating during the wash cycle.
Malfunction of the heating element relay.
Heater sensing relay issue.
Current leakage from the heating element.
Heating element relay failure.
Electrolux washer code E6A indicates control Board Error. Audited diagnosis findings: main control board failure; loose connections at the main…
Electrolux washer code E7 indicates problem with the motor. Audited diagnosis findings: power board failure (models before 2010); cooling fan…
Temperature Sensor Error - Issue with the water temperature sensor (NTC thermistor).
Malfunction of the temperature sensor (increased resistance).
Dryer temperature sensor fault; open circuit in the heater temperature sensing circuit.
Fault in the dryer temperature sensor circuit.
Wash NTC sensor improperly positioned.
Water temperature sensor error; no signal from the thermistor to the control board.
NTC temperature for the cold water valve over the limits; hot and cold water hoses likely switched.
Problem with the water level sensor.
Pump / Filter Blockage - Often related to drain issues, indicating a blockage or pump problem.
Error at the reset position of the program selector. This can sometimes indicate an error in the dosing tray or…
Problem detected in the operation of the program selector.
Error detected while reading data from the selector.
Recirculation pump triac failure.
Recirculation pump failure.
Electrolux washer code E86 indicates incorrect UI table. Audited diagnosis findings: faulty user interface control board; loose or damaged wiring…
User interface microcontroller fault.
Problem with the electronic board.
Communication / PCB Error - Communication fault between control boards or a main control board issue.
Communication error between the user interface and the main control board.
Inconsistent user interface and main control board.
Incorrect configuration of the washing machine's main control board.
Incorrect configuration of the washing machine's cycle.
Communication error between the main board and the display board.
Incompatibility between the hardware version and the appliance's configuration.
Communication error between the main control board and the DSP (Digital Signal Processor).
Incongruence between the sound and light module and the main board.
The firmware between the speaker and the input/output electronics is not in order.
Communication error between micro-processor and FLASH memory.
User interface configuration problem.
Communication error between the main board and the display.
Communication error between the main control board and the user interface.
Communication error between the main control board and peripheral devices (like the motor control board).
Drum positioning system (DSP) defective in top-loading machines.
DSP (Digital Signal Processor) recognition error.
DSP (Digital Signal Processor) communication error.
DSP (Digital Signal Processor) defect; triac for DPS defect.
Faulty DSP (Digital Signal Processor) Thyristor or main voltage sensing failure.
Defective drum door in top-loading machines.
Line safe relay sensing failure.
The frequency of the power supply is incorrect or outside the acceptable range.
The supply voltage is too high.
The supply voltage is too low.
Faulty identification of the protective circuit; sensing circuit on safety system defective.
The water fill valve is blocked.
Security sensor giving an error.
Safety sensor with an anomaly.
Electrolux washer code EC4 indicates current sensor alarm. Audited diagnosis findings: damaged or jammed clutch assembly; loose or damaged wiring…
The drain filter is clogged.
There is too much foam in the drum.
Aquastop system activated.
Electrolux washer code EF5 indicates the load is unbalanced. Audited diagnosis findings: unbalanced load; washer is not level; overloading the…
Electrolux washer code EH0 indicates power supply problem. Audited diagnosis findings: no power to the appliance; unstable power supply; use…
The frequency of the power supply is out of the operational range.
The power supply voltage is too high (higher than ~270V for more than 5 seconds).
The power supply voltage is too low.
Electrolux washer code EHC indicates line WD relay failure. Audited diagnosis findings: main control board failure; low voltage.
Faulty wiring or a defective Printed Circuit Board (PCB).
Safety system sensing circuit fault, indicating an invalid microprocessor input voltage.
Internal fault in the control.
Communication error between the Central Control Unit (CCU) and the Motor Control Unit (MCU).
Communication fault between the touch control board and the main control board.
Bad EEPROM Identification/Checksum error.
Ignition control failure.
Motor control board error.
Overheating fault with the dryer part (in washer-dryer models).
Water temperature problem.
Electrolux washer code F3 indicates water level problem. Audited diagnosis findings: communication failure between the main control board and the…
Electrolux washer code F4 indicates the washer is not advancing through its cycles. Audited diagnosis findings: main control board failure;…
A keypad problem has been detected.
Electrolux washer code F6 indicates control reset. Audited diagnosis findings: motor control board failure; loose wiring connections to the motor…
Water level sensor fault.
Hot and cold water hoses are inverted.
Flood condition detected.
Electrolux washer code HE indicates heating element error. Audited diagnosis findings: no heat detected in a cycle that requires it;…
The child lock feature is activated, preventing changes to the settings.
Electrolux washer code LE indicates water leak detected. Audited diagnosis findings: the machine is overloaded; the laundry load is unbalanced;…
The washing machine does not detect any water entering the tub.
The wash cycle is paused.
The 'Extra Rinse' option has been selected for the current wash cycle.
Electrolux washer code SE indicates sensor error. Audited diagnosis findings: a button on the control panel is stuck; the user…
Electrolux washer code SUDS indicates too many suds detected. Audited diagnosis findings: too much detergent was used; the wrong type…
Electrolux
Demo mode is active.
Drain pump activated.
Door switch is not closed.
Outlet thermistor failure.
Outlet thermistor failure.
Power supply frequency out of range.
Supply voltage is too high.
Supply voltage is too low.
Electrolux Dryer Error H2-B2-2 — Power Supply Issue.
Electrolux Dryer Error H2-B2 — Power Supply Issue.
Electrolux Dryer Error H4-B4-2 — Incorrect wiring.
Electrolux Dryer Error H4-B4 — Incorrect wiring.
Line safe relay short circuit error.
Line safe relay short circuit error.
Line safety circuit errors.
The unit has no sounds or alarm chimes.
Capacitive sensor errors.
Electrolux dryer code 41 indicates door opened at start. Audited diagnosis findings: dryer door was open when the start button…
Electrolux dryer code 9C indicates software/config errors. Audited diagnosis findings: faulty user interface board; failed main control board; loose connection…
Auto Dry setting is selected.
Electrolux dryer code C2 indicates drainage problem. Audited diagnosis findings: clogged or kinked drain hose; blocked drain pump filter; faulty…
Not specified in search results.
Indicates a problem with the temperature sensor.
Communication error between the main board and the UI board.
Electrolux dryer code CE indicates configuration error. Audited diagnosis findings: communication error between the main control board and the motor…
Not specified in search results.
Close door - door switch error.
No error detected during the last cycle.
General EEPROM fault; problem with communication between EEPROM and the microprocessor.
Checksum Error; problem with communications or memory did not check.
Non-fatal R/W error; problem reading or writing to memory or input/output.
Drying error - Requested drying time is longer than maximum allowed.
Gas error - A flame was not detected on gas-heated dryers.
Vacuum switch - The vacuum switch does not shut within 5 seconds after the dryer is started.
Vacuum switch - The vacuum switch was already closed when an attempt to start the dryer was made.
Input sensor disconnected - The inlet thermistor or wiring to the thermistor is open.
Output sensor disconnected - The outlet thermistor or wiring to the thermistor is open.
Electrolux dryer code E20 indicates water doesn't drain. Audited diagnosis findings: blockages in the drain pump or hoses; kinked or…
Faulty canister fill pump triac.
Condensate pump is defective or blocked.
The frequency of the capacitive level sensor is outside the acceptable range.
Fault in the compressor cooling fan sensor circuit.
Electrolux dryer code E30 indicates drum overfilled. Audited diagnosis findings: main control board failure; communication error between the main control…
Moisture sensor frequency is too high.
Moisture sensor frequency is too low.
Pressure sensor indicates water overfill.
Electrolux dryer code E4 indicates humidity Sensor Failed. Audited diagnosis findings: dirty humidity sensor; faulty humidity sensor; damaged wiring to…
Electrolux dryer code E40 indicates door is open. Audited diagnosis findings: dryer door is not fully closed; obstruction in the…
Electrolux dryer code E41 indicates door opened at start. Audited diagnosis findings: loose or broken wiring at the door switch;…
Electrolux dryer code E42 indicates door sensing error. Audited diagnosis findings: door is not closing properly; faulty door switch; obstruction…
Faulty door closing sensor.
Motor or software problem.
Electrolux dryer code E51 indicates motor relay failure. Audited diagnosis findings: motor overheating safety cut-out activated; loose wiring to the…
Motor stopped or not starting.
Motor centrifugal switch failure.
Electrolux dryer code E54 indicates motor sensing failure. Audited diagnosis findings: faulty main control board; failed motor; damaged wiring harness…
Electrolux dryer code E55 indicates motor overheating. Audited diagnosis findings: overloading the dryer; clogged or restricted ventilation; obstructed drum.
Electrolux dryer code E56 indicates high motor current. Audited diagnosis findings: overloading the dryer; obstructed or binding drum; failing drive…
High current on inverter.
High current on motor phase.
The inverter board is overheated.
The motor control board is receiving insufficient voltage.
The input voltage to the inverter board is too high.
A data transfer error has occurred between the inverter board and the main PCB.
There is a communication error between the inverter and the main PCB.
General error indicating damage to the FCV board.
The motor voltage is too low (below 100 volts).
Electrolux dryer code E60 indicates heating problem. Audited diagnosis findings: clogged lint filter; restricted or clogged exhaust vent; damaged door…
Electrolux dryer code E61 indicates heater relay failure. Audited diagnosis findings: faulty heater relay on the main control board; failed…
Power relay to the heater unit is faulty.
Heating element shorted to ground.
Open heating element circuit.
High limit thermostat tripped open too many times.
Thermal limiter tripped.
Electrolux dryer code E67 indicates heating sensor failure. Audited diagnosis findings: faulty electronic control board; temporary glitch in the control…
FCV overcurrent protection.
Incorrect operation of VSC engine.
Outlet thermistor is out of range / Wash NTC failure.
The outlet thermistor is out of range / Problem with the NTC heater.
Inlet thermistor failure.
Drive motor relay failure.
User interface/button stuck/communication issue.
Selector knob/UI input fault.
Incorrect selector setting signal.
Control panel board microcontroller self-test error.
Communication issue between UI and main board.
Communication error between the user interface and the main control board.
Mismatch between the user interface and the main control board.
Control and peripherals are not matched or configured.
Configuration error internal to the main control.
Program mismatch internal to the main control.
Communication error between the main control board and the motor control board.
Low voltage condition detected by the control board.
Incoming power frequency is out of range.
Incoming voltage is above 130 VAC.
Incoming voltage is below 90 VAC.
Incorrect wiring on the terminal block.
Fatal error of the main control.
Line safe relay sensing failure.
Electrolux dryer code EAF indicates watchdog reset. Audited diagnosis findings: microcontroller has been reset by an internal Watchdog timer.
Incoming power frequency out of limits.
Incoming line voltage above 130 VAC.
Incoming line voltage below 90 VAC.
Console control problem.
Console control problem.
Faulty main control board.
Electrolux dryer code EF1 indicates ventilation Blockage. Audited diagnosis findings: ventilation blockage; clogged lint screen; restricted exhaust vent.
Electrolux dryer code EF2 indicates too much soap. Audited diagnosis findings: excessive foam in the drum; using too much detergent;…
Maximum drying time has been reached, but clothes are still wet.
NTC temperature for the hot water valve over the limits.
Electrolux dryer code EF6 indicates control reset. Audited diagnosis findings: control reset; fault on the electronic control board.
Stuck key on the user interface.
A safety line alarm has been triggered, indicating a faulty main board.
Membrane switch failure.
Internal fault in the control.
Control temperature sensor open or shorted.
Electrolux dryer code F03 indicates no heat. Audited diagnosis findings: heating element failure; faulty inlet thermistor/sensor.
The drying time has exceeded the program time for that cycle.
Venting issue or fault in the moisture sensor circuit.
A water temperature problem.
Water level problem caused by incoming or drain pump is not working.
Indicates a heating fault, which could be related to the dryer thermostat, heater element, or outlet sensor.
Wrong variant - Wrong combination of switches on PCB.
Electrolux dryer code F6 indicates control board fault. Audited diagnosis findings: main control board microprocessor fault; loose wiring connections to…
Service program wrongfully engaged.
Electrolux dryer code F9 indicates vacuum switch fault. Audited diagnosis findings: faulty vacuum switch; blocked or kinked tubing connected to…
Electrolux dryer code FL indicates water valve is open. Audited diagnosis findings: informational code displayed during a diagnostic test on…
Power frequency/voltage issues.
Electrolux dryer code HC indicates heating Error - Dryer is getting too hot. Audited diagnosis findings: main control board failure;…
Electrolux dryer code HD indicates main Board Failure. Audited diagnosis findings: main control board failure; loose, disconnected, or damaged wiring;…
Electrolux dryer code HE indicates heating Error - Dryer isn't heating as it should. Audited diagnosis findings: main control board…
Line safe sensing circuit failure (main board failure).
A problem with power to the motor.
Electrolux dryer code UF indicates fan not running. Audited diagnosis findings: faulty vent assembly; obstruction in the vent fan; loose…
Electrolux dryer code UL indicates uL test mode. Audited diagnosis findings: the dryer has been placed in a diagnostic or…
Electrolux dryer code UO indicates vent open. Audited diagnosis findings: stuck or malfunctioning plunger in the vent assembly; faulty optical…
Electrolux
Demo Mode is active.
Demo Mode is active.
The appliance is in demonstration mode.
Manual defrost mode is active.
Manual defrost mode is active.
Ice jam in the dispenser chute.
Ice jam in the dispenser chute.
A door has been open for 5 minutes or more.
A door has been open for 5 minutes or more.
Communication error.
Communication error.
Damper heater error.
Defrost sensor error.
Temperature sensor error.
Temperature sensor error.
The temperature in the refrigerator compartment is below 0°C.
Evaporator sensor malfunction or refrigerant leakage.
Evaporator sensor malfunction or refrigerant leakage.
Fault in the temperature sensor.
Fault in the temperature sensor.
Malfunction of the thermistor sensor.
Malfunction of the thermistor sensor.
Temperature alarm. This indicates that the temperature in the fridge or freezer is too high.
High temperature alert. The temperature inside the refrigerator or freezer is too high.
High temperature alert. The temperature inside the refrigerator or freezer is too high.
Indicates that the internal temperature of the refrigerator or freezer has exceeded a preset safety threshold.
The power supply to the appliance has dropped below 170V.
In diagnostic mode, indicates the absence of a 12V or GND signal for a fan motor when it is on.
In diagnostic mode, indicates no PWM signal is detected for a fan motor when it is off.
Power Failure. Indicates the refrigerator has lost and regained power.
Appears after a power outage to inform the user that the refrigerator has lost and regained power.
Indicates 'reverse piloting' in diagnostic mode.
Electrolux Refrigerator Error SB-OR-SB-2 — Sabbath Mode is active.
Electrolux Refrigerator Error SB-OR-SB — Sabbath Mode is active.
Temperature sensor is shorted. This can apply to either the freezer or refrigerator sensor.
Communication failure between the main control board and the user interface at power-up.
Communication failure between the main control board and the user interface at power-up.
Communication failure between the main control board and the user interface.
Communication failure between the main control board and the user interface.
Evaporator fan circuit failure.
Evaporator fan circuit failure.
A general fault indicator that often accompanies another error code or status alert, such as a high temperature or door…
Indicates that a component is closed during diagnostic mode.
The freezer compartment is not cold enough. This is likely to occur after a long-term power failure.
Refrigerator compartment is not cold enough.
Electrolux refrigerator code E11 indicates the refrigerator compartment is too cold. Audited diagnosis findings: 'Super Cool' mode is activated; temperature…
Door switch error; the control board thinks the door is open.
Door lock device failure.
Showroom Mode is active. The compressor, fan, and defrost heater remain off, while the display shows the set temperature instead…
The thermistor is open or shorted.
Electrolux refrigerator code F1 indicates thermostat error. Audited diagnosis findings: failed thermostat; loose wiring connection to the thermostat.
Electrolux refrigerator code F2 indicates thermostat error. Audited diagnosis findings: failed thermostat; wiring issue with the thermostat.
Temperature error, likely a defective temperature sensor.
Temperature error, indicating a defective temperature sensor.
Temperature error, likely from a defective temperature sensor.
Electrolux refrigerator code F6 indicates power connection error. Audited diagnosis findings: power outage or interruption; refrigerator door left ajar.
Electrolux refrigerator code F7 indicates power connection error. Audited diagnosis findings: unstable power supply; refrigerator door not closed properly.
Electrolux refrigerator code F8 indicates defrost error. Audited diagnosis findings: failed defrost heater; faulty defrost thermostat; defective defrost control board.
Indicates a locked state of a component during diagnostic mode.
Refrigerator temperature sensor is open.
Power Failure. Indicates the refrigerator has lost and regained power.
Refrigerator temperature sensor has shorted.
Electrolux
Electrolux dishwasher code LOC indicates the dishwasher door is locked. Audited diagnosis findings: the child lock feature is activated.
Indicates that the AirDry function, which automatically opens the door at the end of the cycle to improve drying, is…
The drain is not efficient.
The tank has overflowed.
The dishwasher door is open.
The dishwasher door is open.
This indicates a heating element failure, where the water did not reach the proper
This indicates a heating element failure, where the water did not reach the proper temperature in the allotted time.
This indicates a heating element failure, where the water did not reach the proper
A water leak has been detected.
There is a failure with the thermistor or turbidity sensor.
A wash motor failure has occurred.
There is a failure with the upper fan or vent.
There is a failure with the upper fan or vent.
There is a failure with the upper fan or vent.
A lower fan failure has occurred.
A lower fan failure has occurred.
There is a failure with the drain valve.
There is a failure with the drain valve.
There is a failure with the drain valve.
A user interface control failure has occurred.
A user interface control failure has occurred.
There is a communication failure between the user interface control and the electronic control
There is a communication failure between the user interface control and the electronic control
An electronic control board relay failure has occurred.
There is a drain valve position error.
An electronic control board failure has occurred.
A green light projected on the floor below the appliance indicates that the washing program is complete.
The dishwasher is in "Heat Delay" or "Heater On" mode, allowing the water to
The dishwasher is in “Heat Delay” or “Heater On” mode, allowing the water to
Water supply error.
The dishwasher is not draining water properly. This can be caused by a clogged drain system, a defective or blocked…
Draining issue. The dishwasher is not draining water properly.
Draining issue. The dishwasher is not draining water properly.
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
Water in the dishwasher base.
Clogged filter or sump. Food soil has built up in the filter system.
Clogged filter or sump. Food soil has built up in the filter system.
Clogged filter or sump. Food soil has built up in the filter system.
No pressure sensor signal.
Pressure sensor calibration invalid.
Pressure sensor signal too high.
Low pressure sensor signal.
There is a problem with the wash motor or the circulation pump. This could be due to a short circuit…
AC wash pump motor problem.
Electrolux Dishwasher Error I52 — Wash pump motor issue.
Electrolux Dishwasher Error I53 — Wash pump motor issue.
Wash pump motor issue.
DCLink low voltage.
DCLink overvoltage.
Wash pump motor issue.
Wash pump motor connection fault.
Wash pump current read ADC fault.
Wash pump over temperature or overload.
Electrolux Dishwasher Error I5B — Wash pump motor issue.
Drain pump motor abnormal high current detected.
Electrolux Dishwasher Error I5D — Wash pump motor issue.
Drain pump motor connection fault.
Water heating problem. The dishwasher is not heating the water correctly.
Water heating problem. The dishwasher is not heating the water correctly.
Heating over temperature.
Water temperature too high or temperature sensor malfunction.
There is an open or short-circuit of the NTC thermistor (temperature sensor). The program
There is an open or short-circuit of the NTC thermistor (temperature sensor). The program
Communication error with the electronic control board (EEPROM fault).
Communication error with the electronic control board (EEPROM fault).
Indicates a fault with the main Printed Circuit Board (PCB) or a communication error between electronic components. This could be…
Indicates that the spray arms are not rotating. This could be caused by improperly placed dishes obstructing the arms or…
Turbidity sensor problem.
Communication failure between the user interface and the main control board.
Communication error with the main control board.
Communication error with the main control board.
Communication error with the main control board.
Motor tacho fault.
Water replenishment timeout or overfilling issue.
The water level inside the appliance is too high.
The dishwasher has exceeded the permissible time for filling with water. The cycle may continue with a small amount of…
High water level / Diverter valve fault.
Indicates a turbidity sensor error. This is an alternative display for the iB0 code. The alarm is triggered if the…
This indicator lights up when the dishwasher's interior needs cleaning using the Machine Care program.
A red light projected on the floor below the appliance indicates that a washing program is in progress. A flashing…
This indicates a shorted keypad.
This indicates a shorted keypad.
Indicates that the TimeSaver option, which reduces the cycle duration, is activated.
Comes on when the sensor for the automatic program is operating to detect the soil level of the dishes.
The delayed start option has been activated. The number indicates the hours of delay remaining.
This number indicates the minutes remaining in the current wash cycle.
Indicates a drainage problem, which could be caused by a clogged filter, a blocked or kinked drain hose, or a…
Signals that a leak has been detected and the anti-flood system has been activated. This can be due to an…
Literal displayed code A1 is documented on Electrolux Professional commercial hood-type dishwashers as the NO WATER alarm; household Electrolux dishwashers…
Electrolux dishwasher code AL5 indicates water inlet problem. Audited diagnosis findings: water tap not fully open or inadequate water pressure;…
Electrolux dishwasher code AL6 indicates draining problem. Audited diagnosis findings: draining fault where the pressure switch incorrectly detects water in…
Electrolux dishwasher code B1-2 indicates the drain is not efficient. Audited diagnosis findings: inefficient draining; clogged or kinked drain hose;…
Electrolux dishwasher code B2-2 indicates the tank has overflowed. Audited diagnosis findings: tank overflow; clogged water drain; malfunctioning pressure switch.
Boiler temperature rising too fast.
Tank level sensor is out of order.
Draining problem or boiler temperature is too high on professional models.
The tank temperature is too high.
Tank temperature sensor out of order.
Tank temperature sensor out of order.
Boiler temperature sensor out of order.
Boiler temperature sensor out of order.
Boiler does not empty during the rinse phase.
Automatic hood is out of order.
The door has been left open or isn't properly latched.
A leak has been detected in the base of the dishwasher.
Tank temperature is low.
The pressure switch signal has not stabilized, indicating a potential water filling issue. This is not typically displayed to the…
Indicates a draining problem, which could be caused by a clogged drainage system or incorrect installation.
Electrolux dishwasher code F21 indicates water softener error. Audited diagnosis findings: low salt in water softener reservoir; leaks in the…
The appliance is in program selection mode.
The dishwasher has experienced a power failure.