Electrolux Washer error code
Electrolux Washer Error E8
Problem with the water level sensor.
Problem with the water level sensor.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Check 1
Turn the washer off and unplug it for a few minutes, then plug it back in and try to start a cycle.
- 2Check 2
Inspect the wiring connections between the motor and the motor control board for any loose or damaged wires.
- 3Check 3
If you have a multimeter, you can test the motor for continuity. A lack of continuity indicates a faulty motor.
A quick explanation
What does E8 mean?
Problem with the water level sensor.
The answer you came for
How to fix Electrolux washer error E8
Start with the safest checks and work from simple to technical.
- 1
Step 1
1. Unplug the washer from the wall outlet for at least 15 minutes to perform a hard reset of the main control board, which can clear temporary electronic glitches.
- 2
Step 2
2. Plug the washer back in and attempt to start a new cycle to see if the error is resolved.
- 3
Step 3
3. If the error returns, check for and remove any excessive suds inside the drum. Too much soap can create foam that confuses the water level sensor. Run an empty 'Rinse & Spin' cycle to clear it out.
- 4
Step 4
4. Verify the drain hose installation. Ensure the hose is not pushed too far into the standpipe (no more than 6-8 inches), as this can create a siphon effect and trigger a water level error.
- 5
Step 5
5. For advanced troubleshooting: disconnect the washer from power and water, then remove the top panel by unscrewing the screws at the back of the machine.
- 6
Step 6
6. Locate the circular water level sensor. Carefully inspect the thin plastic or rubber tube connected to it. Check the entire length of the tube for any kinks, blockages, or loose connections at either the sensor or the tub.
- 7
Step 7
7. If the tube is clear and secure, reattach the top panel. If the error persists after all these steps, the issue likely lies with a faulty sensor or control board, which requires professional diagnosis.
What may be causing it?
- Faulty motor
- Defective motor control board
- Loose or damaged wiring between the motor and control board
These are possibilities to investigate, not proof that one part has failed.
Recommended part
Recommended part for this error code
Replacement part
OEM candidate: 134638900
Why this part is shown: It is associated with Electrolux Washer error E8 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete washer model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your washer?
If repairing this washer no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, FREE delivery on eligible items
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$599
Budget-friendly washers in the $0-$599 range.
Shop Value Options on AmazonBest Overall
$600-$999
Balanced washers in the $600-$999 range.
Shop Best Overall Options on AmazonPremium
$1,000-$2,500
Higher-end washers in the $1,000-$2,500 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Washer Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.Reviewed by the Appliance Fix Guide Editorial Team
- Researched against manufacturer documentation and service literature where available.
- Safety-first structure: every guide starts with the safest first action and states when to stop and call a professional.
- Part compatibility is treated cautiously: fitment must be confirmed against the exact model number before purchase.