How to Fix Samsung Washer Error 4E
Water supply error — washer not filling
325 repair guides
Choose the appliance, then find the exact code. Every guide leads with what the code means, what to try first, and whether a part or replacement is worth considering.
Samsung
Water supply error — washer not filling
Jammed button on control panel
Water overflow — tub level too high
Water overflow — tub level too high
The washer timed out while trying to fill with water. Ensure your home water taps are fully turned on and…
This code indicates the hot and cold water supply hoses for the upper FlexWash
Voltage error (FlexWash)
Voltage error (FlexWash)
Water level sensor error or leak detected
FlexWash upper latch rubber button missing
Water level sensor frequency out of range - pressure switch fault
Unbalanced load (FlexWash)
UNPLUG washer from electrical power.
Voltage / power supply error
The water level is too high. This implies the water valve is leaking into the tub or the air hose…
The washer cannot detect the motor’s speed or position. This is usually caused by a failed Hall Sensor on the…
Motor error (alias for 3E3)
Motor error (alias for 3E4)
Motor tachometer/hall sensor signal error - no speed feedback to inverter
Motor overload due to excessive laundry load or mechanical binding
Erratic motor speed signal or hall sensor intermittent fault
Motor phase imbalance detected by inverter - winding fault or PCB issue
Motor stall detection during acceleration - mechanical binding or sensor fault
The load is unbalanced during the spin cycle. If the load is evenly distributed but this error persists, the suspension…
Water inlet valve malfunction or reversed hot/cold hose connections
This code indicates the hot and cold water supply hoses for the main washer
Water temperature sensor fault during fill cycle
Incoming water temperature exceeds 50°C (122°F) for delicate cycles
The water is not heating up. The heating element inside the tub is likely burned out or disconnected. The temperature…
Drain pump obstruction or pressure switch fault causing False full-tub signal
Excessive suds detected
Detergent drawer not fully closed
Drain system fault - pump failure or main PCB relay issue
System fault sub-classification
System relay error
Excessive suds detected
Excessive suds detected
The water is heating up uncontrollably fast. The heater relay on the main circuit board is likely fused shut. The…
Motor speed sensor error
Jammed button on control panel
The pressure switch (water level sensor) signal is missing. The washer won't run because it doesn't know how much water…
SilverCare system error (older models)
Flash code: 8 flashes = Overcurrent error; motor overload or short
MEMS vibration sensor error
Unplug the washer from the power outlet.
MEMS vibration sensor error
Overcurrent error - excessive amperage draw detected by inverter protection circuit
MEMS sensor error (or button error, model-dependent)
The washer detects irregular voltage from the power outlet. This can be a home electrical issue, but often it is…
DC bus overvoltage on inverter circuit (>400V DC) - rectifier or capacitor fault
DC bus undervoltage on inverter circuit (
High temperature circuit fault – heater element or thermostat failure
Hardware overcurrent - physical short circuit detected (fire hazard)
Software overcurrent – current sensing circuit fault or False trigger
Low voltage detection (
High voltage detection (>140V AC) or power anomaly triggering protection
Communication error between main PCB and sub PCB/control panel
Button error; control panel key stuck or shorted
Power button held >13 seconds or stuck switch causing control fault
Calibration mode active
Calibration mode active
Heater relay stuck closed or temperature runaway condition
Child Lock enabled
Door open during operation attempt or door switch not detecting closure
This is a door lock error.
This error is specific to the small 'AddWash' door on the main door.
This error is specific to the small 'AddWash' door on the main door.
Door not locked or door switch fault preventing cycle start
Door lock mechanism failure during operation (lock disengaged mid-cycle)
This is a door lock error.
Software update downloading
The machine is not filling with water fast enough. Check for kinked hoses or clogged screens on the water inlet…
The washer is not draining. This is almost always a clogged drain pump filter (coin trap) or a broken drain…
UNPLUG washer from electrical power.
UNPLUG washer from electrical power.
UNPLUG washer from electrical power.
Water leakage (legacy code)
Motor tachometer / hall sensor error (legacy)
Water level sensor fill error - incorrect level detection during fill cycle
Flood condition; water leak detected by floor sensor under tub
Flash code: 1 blink pattern = door lock system fault (models without display)
Flash code: 3 blink pattern = drain system fault (models without display)
Flash code: 4 blink pattern = motor/hall sensor fault (models without display)
Heater circuit fault - open circuit or short in heating system wiring
UNPLUG washer from electrical power.
UNPLUG washer from electrical power.
The water is getting too hot, or the sensor thinks it is. This is often a relay on the main…
Heating circuit failure
Water inlet failure; valves not opening, clogged screens, or pressure sensor issue
This is a door lock error code, despite its appearance.
Leak detection sensor activated - moisture detected in base pan
Overflow condition detected by leak sensor system - tub overfilled
Alternative leak detection code on specific Samsung models (WF350 series)
Door lock timeout; lock fails to engage within 60 seconds
No drain - water not evacuating within 15 minutes
No fill - water not entering drum within 40 minutes
Hot/cold water supply hoses reversed
Water overflow — tub level too high
Overflow error - excessive water detected in tub beyond maximum level
Water overflow detected during the fill cycle. The cold water inlet valve may be mechanically stuck open, forcing water into…
UNPLUG washer from electrical power.
Water overflow — tub level too high
Pause error; cycle interrupted unexpectedly (door opened mid-cycle)
Pressure switch error; water level sensor malfunction
Clutch hall sensor error
Power failure during cycle operation - informational code after outage
Auto dispenser empty (softener)
Rare code: Steam generator error (steam-capable models)
The washer detects too many suds. This happens when you use non-HE detergent or too much soap. The cycle pauses…
Detergent drawer not fully closed
Alternative drain error code on specific Samsung models (WF45T series)
System fault sub-classification
System relay error
Excess suds detected - non-HE detergent or overdosing causing foam buildup
This code means the machine has detected too many suds.
Temperature control error; heater not reaching target temp
The temperature sensor (thermistor) is broken or disconnected. The machine has stopped heating because it cannot read the water temperature.…
Heating element thermistor fault (models with water heater)
Inlet water thermistor fault (cold water monitoring sensor)
Thermistor signal out of range - PCB interpretation error or reference voltage fault
Unbalanced load — washer cannot spin
Alternative display format for unbalanced load error on specific models
Rare code: Unbalanced during spin with suspension fault detected
Unstable current/voltage supply detected during operation - fluctuation >15%
Unbalanced load detected during spin cycle
Unbalanced load — retry in progress
Samsung
UNPLUG dryer from electrical power.
Flash code: 10 flashes = Control board processor fault (non-display models)
Door error (FlexDry models)
Door error (FlexDry models)
Temperature sensor fault (FlexDry models)
Temperature sensor fault (FlexDry models)
UNPLUG dryer from electrical power.
Abnormal voltage / Over voltage error
UNPLUG dryer from electrical power.
Motor error / Inverter motor check
Disconnect the dryer from power at the circuit breaker.
Drive motor failure
UNPLUG dryer from electrical power for 10 minutes to reset electronics.
UNPLUG dryer from electrical power.
Drain tank overflow / Drainage problem
UNPLUG dryer from electrical power.
UNPLUG THE DRYER. This error means a button on the user interface (UI) is
UNPLUG THE DRYER. This is an alias for 6C2, indicating a stuck button on
Flash code: 7 flashes = Power supply fault (non-display models); voltage instability or outage
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power for 20 minutes to attempt deep memory reset.
Abnormal voltage supply / Over voltage error
Communication error between main board and Wi-Fi board
UNPLUG THE DRYER. This is a communication error between different control boards.
UNPLUG THE DRYER. This is a communication error between different control boards.
Communication error between main and inverter PBA
UNPLUG THE DRYER. This error means a button on the user interface (UI) is
UNPLUG dryer from electrical power.
UNPLUG THE DRYER. This is an alias for bC2, indicating a stuck button on
Laundry detected in drum during vent blockage test
This is a critical safety warning, not a fault with the dryer.
This is a critical safety warning, not a fault with the dryer.
Vent is over 90% clogged
UNPLUG dryer from electrical power for 10 minutes to reset electronics.
UNPLUG dryer from electrical power for 10 minutes to reset electronics.
UNPLUG dryer from electrical power for 10 minutes to reset electronics.
Child Lock activated
Vent is clogged (100%)
UNPLUG dryer from electrical power.
Door circuit failure
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power for 10 minutes to reset electronics.
UNPLUG dryer from electrical power.
Control board memory error; EEPROM corruption or processor fault (older models)
UNPLUG dryer from electrical power immediately.
UNPLUG dryer from electrical power for 20 minutes to attempt deep reset.
Invalid power source frequency
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
UNPLUG THE DRYER. This is a critical over-temperature fault. The number one cause is
Alternate representation of heater circuit fault; identical failure mode to HE code
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
Lint filter problem / Check filter
Excessive dry time
UNPLUG dryer from electrical power immediately.
Power failure detected during cycle; voltage drop, outage, or unstable household power
Steam system fault; condenser blockage, generator failure, or water supply issue (steam-capable models only)
UNPLUG dryer from electrical power.
Alternate representation of exhaust thermistor fault; identical failure mode to tE code
UNPLUG dryer from electrical power.
UNPLUG dryer from electrical power.
Temperature sensor fault
Samsung
Unplug refrigerator from electrical power or switch off dedicated circuit breaker.
Verify household voltage at refrigerator outlet using multimeter.
Flex room defrost sensor error - alias of 11E
Flex room / Cool Select Zone defrost sensor error
UNPLUG THE REFRIGERATOR.
Humidity sensor error
Ice maker sensor error - alias of 14E
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power or switch off dedicated circuit breaker.
Flash code 2: Refrigerator temperature sensor fault (non-display models); identical failure mode to 2E code
Freezer evaporator fan error - alias of 21E
Unplug refrigerator from electrical power.
Refrigerator evaporator fan error - alias of 22E
Unplug refrigerator from electrical power.
Condenser fan error - alias of 23E
Unplug refrigerator from electrical power.
Freezer defrost function error - alias of 24E
Unplug refrigerator from electrical power.
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power.
Unplug the refrigerator.
Unplug the refrigerator.
UNPLUG THE REFRIGERATOR.
Flex Zone defrost system error
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power or switch off dedicated circuit breaker.
Unplug refrigerator from electrical power.
UNPLUG THE REFRIGERATOR.
Flex Zone / CV-Fan motor error
Ice pipe heater error - alias of 33E
Unplug refrigerator from electrical power.
Ice maker communication error; alternate code variant indicating same ice maker system fault as 39E
Ice maker function error; communication failure between ice maker assembly and main control board
UNPLUG THE REFRIGERATOR.
Refrigerator defrost sensor error - wire cut, short circuit, contact failure, or missing sensor
Unplug refrigerator from electrical power.
Ice room fan error - alias of 40E
UNPLUG THE REFRIGERATOR.
Family Hub software/system error - blue interior lights flashing
Family Hub update issue - software update glitch on 3-Door French Door Family Hub models
Unplug the refrigerator.
Family Hub software/system error - blue interior lights flashing
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power.
Flash code 7: Power supply fault (non-display models); voltage instability or temporary outage
AutoFill infuser overflow detected - water detected in AutoFill compartment
AutoFill infuser overflow detected - alias of 76C
UNPLUG THE REFRIGERATOR.
Unplug refrigerator from electrical power.
Compressor abnormal current detection; excessive current draw indicating mechanical failure or electrical fault
Compressor locked - motor locked error
Verify household voltage at refrigerator outlet using multimeter.
Unplug refrigerator from electrical power.
Communication fault - power disrupted during bootup; refrigerator did not boot properly
Communication error between main control board and display/interface board
Display board fault; LCD panel failure, button matrix error, or communication loss with main board
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power for 15 minutes to attempt deep memory reset.
Unplug refrigerator from electrical power.
Water inlet valve fault; solenoid coil failure or mechanical valve malfunction preventing water flow
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
Door switch fault; reed switch or mechanical switch malfunction detecting door open/closed status
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power.
Unplug refrigerator from electrical power for 15 minutes to attempt deep memory reset.
Verify household voltage at refrigerator outlet using multimeter.
Self-diagnostic mode after power outage or initial plug-in - normal startup behavior
Ice bucket not properly installed or missing - ice maker will not operate
Cooling Off Mode (Demo Mode) - display variant of OF OF
Manual operation mode 2 (diagnostic test mode sequence step 2)
Cooling Off Mode (Demo Mode) - display variant
Communication error between main control panel and touch panel - variant of PC ER
Samsung
Unplug dishwasher and turn off water supply valve.
Flash code 10: Control board processor fault; hardware failure requiring board replacement (non-display models)
Filter clogged / Load or detergent issue
Inlet water temperature sensor fault; thermistor open, shorted, or out of operational range
Flash code 2: Drain system failure; pump obstruction or motor fault (non-display models)
Unplug dishwasher from electrical power.
Water supply error; insufficient water pressure or flow during fill cycle
Immediately unplug dishwasher and turn off water supply valve.
Unplug dishwasher and allow components to reach room temperature.
Water inlet restriction; clogged filter screen at inlet valve
Unplug dishwasher and turn off water supply valve.
Unplug dishwasher and remove lower access panel.
Unplug dishwasher and open door.
Drain pump failure; seized impeller, motor fault, or electrical open circuit
Unplug dishwasher from electrical power.
Unplug dishwasher and open door.
Unplug dishwasher from electrical power.
Flash code 7: Power supply fault; voltage instability or temporary outage (non-display models)
Unplug dishwasher for 10 minutes to reset electronics.
Unplug dishwasher and open door.
EEPROM memory error; corrupted firmware or processor fault on main control board
Flash code 9: EEPROM/memory error; corrupted firmware or processor fault (non-display models)
Heater relay fault; relay stuck open/closed or control board circuit failure
Alternate leakage error; moisture sensor activated (regional variant of 3E)
Access Point mode for mobile/Wi-Fi connection
Unplug dishwasher from electrical power.
Unplug dishwasher for 10 minutes to reset electronics.
Unplug dishwasher from electrical power.
Unplug dishwasher and remove lower access panel.
Heating temperature sensor fault; thermistor open/shorted or out of range during heat cycle
Unplug dishwasher from electrical power.
Communication error between main board and auxiliary components (alternate CE variant)
Immediately unplug dishwasher and turn off water supply valve.
Unplug dishwasher and allow 30 minutes for components to cool completely.
Ventilation fan fault; fan motor failure or blocked air duct (models with fan drying)
Water level sensor fault; pressure switch malfunction or air hose blockage
Unplug dishwasher and allow 30 minutes for components to cool completely.
Unplug dishwasher and allow 30 minutes for components to cool completely.
Water inlet error; insufficient water flow detected during fill cycle
Low current error; insufficient power to heater circuit indicating relay or board fault
Unplug dishwasher and remove lower access panel.
Overflow error; water level exceeds safety limit due to drain failure or sensor fault
Unplug dishwasher and turn off water supply valve.
Unplug dishwasher from electrical power.
Unplug dishwasher and allow components to reach room temperature.
Communication fault; data transmission error between control boards or sensors