How to Fix LG Washer Error 1E
A problem with the water supply.
166 repair guides
Choose the appliance, then find the exact code. Every guide leads with what the code means, what to try first, and whether a part or replacement is worth considering.
LG
A problem with the water supply.
Unplug washer and wait for discharge
Cold water inlet error - issue with cold water supply
Water supply error - fill time exceeded maximum limit
Drain error - water not draining within time limit
Unplug washer and access pressure switch
Disconnect power from washer
Heater error - water temperature not reaching target
Communication error - control board signal fault detected
AC current error - main power supply current abnormality
Leak detected (front-load) OR gear/auto-restart error (top-load) - meaning varies by washer type
Button error - control panel button malfunction
Cool Down - drying cycle complete; periodic tumbling to prevent wrinkles
Over-current error in motor electrical circuit - caused by short circuit, loose connection, or power surge
Motor current zero error - no current detected in motor circuit
Unplug washer and wait for discharge
Child Lock active - control panel is disabled; not an error code
On top-loading models, this is a combined error for door closure and an unbalanced load.
Door lock error - washer door/lid was unable to lock
Door error zero - door lock signal not detected
Door not closed properly - laundry may be caught between door and rubber gasket
Door/lid not properly latched - primarily for SideKick pedestal washer
A variant display for the ‘dE1’ error, indicating the washer’s door is open and
A variant display for the ‘dE1’ error, indicating the washer’s door is open and
Dry function error (temporary) – issue with heater in washer/dryer combo during drying cycle
Door lock error - door lock mechanism failed to engage
Overflow error - alias of FE on newer models
Overflow error zero - water level sensor zero fault
Overflow error variant 1 - pressure switch stuck closed
Overflow error variant 2 - inlet valve stuck open
Flood error - water leak detected by base sensor
Disconnect power from washer
Hot and cold reversed - water inlet hoses connected incorrectly
Heater error - temporary heating element malfunction
Heater sensor error - temperature sensing circuit fault
Inlet communication error - water valve signal fault
Leak check mode - washer in leak detection test mode
Locked motor with possible water level sensing error - motor obstruction on top-load models
Motor locked error variant 2 - motor hall sensor failure
Low water pressure - inlet water pressure below minimum
Drain error variant 1 - drain pump not activating
Drain error variant 2 - drain pump running but not draining
Water level pressure sensor malfunction - sensor unable to detect water level correctly
Unplug washer and access pressure switch
Pressure error variant 1 - pressure hose disconnected or cracked
Disconnect power from washer
Sensor error - motor sensor (hall sensor) malfunction
Tub Clean reminder - time to run tub clean cycle; appears every 30 cycles
Heating/temperature error - usually caused by faulty thermistor (temperature sensor)
Disconnect power from washer
Vibration sensor error – display variant of vS
Unbalance error variant 1 - load shift detected during spin
Unbalance error varian 2 - excessive vibration detected
Vibration sensor error - display variant of vS
Unplug the washer from the power outlet.
LG
Exhaust duct 80% clogged - significant airflow restriction; on gas dryers may also indicate lack of gas supply
Display message for GAS - 7-segment display renders 'GAS' as '9A5'; same as gAS error
Add Water. On Steam Dryer models with a manual reservoir, the water level is too low to generate steam.
Button Error. A button on the user interface is stuck in the pressed position.
Cool Down - drying cycle complete; periodic tumbling to prevent wrinkles
How to Fix Dryer Error Remove the lint filter.Clean off all lint.Reinsert the filter.Press
Child Lock. Not a failure, but a status preventing operation. Buttons are locked.
Allow the dryer to finish tumbling to prevent wrinkling.
Disconnect the flexible vent hose from the back of the dryer.
Disconnect the flexible vent hose from the back of the dryer.
Open the door and inspect the latch assembly for physical damage.
Door Error 1. The control board assumes the door is open while the cycle is running, or the switch circuit…
Door Error 2. The control board assumes the door is CLOSED when it should be open (Switch contacts welded shut).
Door Error 3. The door is detected as open, but the start button is being pressed.
Door Lock Error (Specific to dryers with door lock safety mechanisms). The dryer cannot verify the door is locked before…
Dry heater error (temporary) - temporary issue with dryer heater
Open and close the dryer door.
Drain Pump Failure (Washer/Dryer Combo units). The unit cannot drain water during the dry cycle.
Drain Timeout. The dryer (condenser type) took too long to empty the reservoir.
Heater Thermistor Circuit Open. Similar to tE1 but specific to certain hybrid firmware.
Disconnect the thermistor plug.
Motor Relay Failure. The motor relay on the main board is stuck.
Remove the top and front panel (or rear panel on some models) to access
Water Drain Error (Combo units). Water level in the tub is not decreasing.
Drain Error (Hybrid/Condenser models). The condensate drawer is full or the drain hose is kinked.
Ensure the room temperature is above 45°F.
Motor Error. The motor is not turning or the belt is broken (on models with belt detection).
Open the door and inspect the latch assembly for physical damage.
Control Board Overheat. The main PCB detects high internal temperature.
EEPROM Error. The main control board's memory is corrupted.
Electrical/heater notification - air temperature or humidity in tub too high during cycle
No Heat (Electric) - Not a display code, but a system state. High Limit Thermostat tripped.
Remove the top and front panel (or rear panel on some models) to access
Fill Error (Washer/Dryer Combo). The water valve is stuck open, filling the unit with water during the dry cycle.
Press Start/Pause to begin the cycle.
No Heat (Gas) - Not a display code, but a system state. Thermal fuse tripped.
Gas Valve Motor Error. The main board does not detect the gas valve coils opening or the igniter functioning correctly.
High Ambient Temperature. The room temperature is too high for the heat pump/condenser to operate efficiently.
Heater Relay failure. The main board detects the heater relay is stuck closed (heating when it shouldn't).
Humidity Sensor Error. The control board detects a short or open circuit in the moisture sensor bars located inside the…
Motor Locked Error. The drum is overloaded or the motor is physically seized.
Wait for cycle to complete.
No Power to the heater (Electric models only). The control board detects that the dryer is not receiving the full…
Output Error / Drain Error. On condenser dryers, the sump pump is unable to evacuate water.
Pressure Sensor Error (Washer/Dryer Combo). The water level sensor is malfunctioning.
Power Failure. The dryer experienced a loss of power during the cycle.
Power Supply Error. The main control board detects improper voltage setup (often improper neutral/ground bonding) or high voltage spikes.
Remove the top and front panel (or rear panel on some models) to access
Ensure the room temperature is above 45°F.
Thermistor Error 3. The thermistor detected a temperature change that is too rapid or inconsistent with the heating profile.
Thermistor Error 4. Specific to Heat Pump/Hybrid dryers. The compressor thermistor is faulty.
LG
Cancel/Drain. Indicates the CANCEL function is active and unit is draining.
Delay Start. Indicates the number of hours the start is delayed (e.g., 03 = 3 hours).
Time Remaining. Estimated cycle time is less than 2 hours.
Leak Error. Water detected in the base pan (flood switch tripped).
Bubble Error. Excessive suds detected.
Consult a technician for diagnosis and repair.
Cool Dry. Unit is running the Cool Dry phase to reduce steam and cool dishes.
Current Error / Motor Error. Indicates an issue with the motor or its wiring harness.
Child Lock / Control Lock. Keys are locked to prevent accidental changes.
Test Mode. Unit is in diagnostic/test mode.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Leak Error. Water detected in the base pan (flood switch tripped). Equivalent to code AE.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Auto Open Door Error. The mechanism to pop the door open for drying has failed.
Combined Water Supply/Leak Error. Indicates water supply exceeds standard amount, oversudsing, or leveling issues.
Consult your owner's manual.
Consult your owner's manual.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Heater Error. Water failed to heat or overheated (above 149°F).
Consult your owner's manual.
Consult a technician for diagnosis and repair.
Water Inlet Error. The unit did not reach the required water level after 10 minutes of filling.
Rinse Aid Level. Indicates current rinse aid dispenser setting (L0=Off, L4=High).
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Consult a technician for diagnosis and repair.
Motor Error. Circulation motor malfunction or wiring issue.
Vario Motor Error. Issue with the vario motor (diverter) controlling spray arms.
Consult a technician for diagnosis and repair.
Drain Error. The unit is unable to drain water within the allotted time.
Download Cycle: Pots & Pans. Cleans heavily soiled cookware.
Download Cycle: Casseroles. Cleans greasy and heavily soiled dishes.
Download Cycle: Glassware. Safely washes delicate glassware.
Download Cycle: Night Care. Quietly washes dishes overnight.
Pressure Sensor Error. Issue with the water level sensor.
Power Failure. Indicates a disruption in power supply.
Consult a technician for diagnosis and repair.
Thermal Error. Water temperature sensed above 194°F or thermistor failure.
Consult a technician for diagnosis and repair.
LG
The microwave is in a cooling cycle. The fan will run until the oven's temperature drops.
LG microwave code DOOR indicates the microwave door is not closed properly. Audited diagnosis findings: door is not properly closed;…
There is an issue with the thermistor, which is essential for temperature regulation. This could be due to a loose…
The temperature in convection mode is not rising as it should.
In convection mode, the achieved temperature is more than 70°C when the user has set a temperature of 40°C.
A key on the control panel is shorted or stuck.
There is a touchpad error, indicating the control panel is not responding correctly.
Indicates a mainboard failure.
A key on the control panel has been shorted for more than a minute.
In convection cooking mode, the temperature is above 100°C even after the maximum time of 30 minutes.
LG microwave code F2 indicates there is a thermistor error. Audited diagnosis findings: faulty thermistor; open or shorted thermistor circuit.
There is a control panel malfunction or a key error. It can also indicate a temperature sensor error.
This indicates a humidity sensor fault.
There is a damper switch error. It can also indicate a problem with the humidity sensor.
This indicates a magnetron or inverter error.
The control lock (child lock) is active, preventing accidental use.